Zanussi Dishwasher ZDS 2010 User Manual

EN  
User manual  
Dishwasher  
2
ZDS 2010  
 
• Do not change the specifications or modify this prod-  
uct. Risk of injury and damage to the appliance.  
• Do not use the appliance:  
Contact your local Service Force Centre.  
• Do not drill into the sides of the appliance to prevent  
damage to hydraulic and electrical components.  
– if the mains cable or water hoses are damaged,  
Warning! Carefully obey the instructions for  
electrical and water connections.  
– if the control panel, worktop or plinth area are dam-  
aged, that you can get access to the inner side of  
the appliance.  
Control panel  
6
1
2
3
4
5
6
Programme knob  
Start/cancel button (Cancel)  
Delay start button (Delay)  
Indicator lights  
Programme marker  
On/off indicator light  
Indicator lights  
End-of-programme  
Comes on when the washing programme is completed. Auxiliary  
functions:  
• Level of the water softener.  
• An alarm if the appliance has a malfunction.  
1)  
Comes on when it is necessary to fill the salt container. Refer to the  
chapter 'Use of dishwasher salt'.  
Salt  
After you fill the container, the salt indicator light can continue to  
stay on for some hours. This does not have an unwanted effect on  
the operation of the appliance.  
1)  
Comesonwhenitisnecessarytofilltherinseaid. Refertothechapter  
'Use of rinse aid'.  
Rinse aid  
1) When the salt and/or the rinse aid containers are empty, the related indicator light does not come on while a washing programme  
operates.  
3
 
– The on/off indicator light goes off (position OFF).  
Delay start button  
Use the delay start button to delay the start of the washing  
programmewithanintervalof3hours. Refertothechapter  
'Setting and starting a washing programme'.  
Programme knob and on/off indicator light  
• To set a washing programme, turn the programme  
knob clockwise or anticlockwise. The programme  
marker on the programme knob must agree with one  
of the washing programmes on the control panel.  
– The on/off indicator light comes on (position ON).  
• To set the appliance to the off position, turn the pro-  
gramme knob until the programme marker agrees with  
the on/off indicator light.  
Washing programmes  
Washing programmes  
Programme  
Programme knob  
position  
Degree of soil  
Heavy soil  
Type of load  
Programme description  
Prewash  
Main wash up to 70°C  
2 intermediate rinses  
Final rinse  
Intensive 70°  
Crockery, cut-  
lery, pots and  
pans  
Drying  
Normal 65°  
Normal soil  
Crockery and  
cutlery  
Prewash  
Main wash up to 65°C  
2 intermediate rinses  
Final rinse  
Drying  
1)  
Normal or light  
soil  
Crockery and  
cutlery  
Main wash up to 65°C  
Final rinse  
Quick 65° A 30'  
2)  
Normal soil  
Crockery and  
cutlery  
Prewash  
Economy 50°  
Main wash up to 50°C  
1 intermediate rinse  
Final rinse  
Drying  
Prewash  
Any  
Partial load (to be 1 cold rinse (to prevent food  
completed later scraps to bond).  
in the day).  
Detergent is not necessary with  
this programme.  
1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load breakfast and  
dinner crockery and cutlery.  
2) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.  
Consumption values  
Programme  
Intensive 70°  
Normal 65°  
Duration (in minutes)  
65 - 75  
100 - 110  
Energy (in kWh)  
1,5 - 1,7  
1,4 - 1,5  
Water (in litres)  
18 - 20  
18 - 20  
4
 
Programme  
Quick 65° A 30'  
Economy 50°  
Prewash  
Duration (in minutes)  
Energy (in kWh)  
Water (in litres)  
30  
0,8  
8
120 - 130  
11  
0,8 - 0,9  
0,1  
12 - 13  
5
The pressure and temperature of the water, the var-  
iations of power supply and the quantity of dishes  
can change these values.  
Use of the appliance  
Refer to the following instructions for each step of pro-  
cedure:  
5. Set the correct washing programme for the type of  
load and soil.  
1. Make a check if the water softener level is correct for 6. Fill the detergent dispenser with the correct quantity  
the water hardness in your area. If necessary set the  
water softener.  
of detergent.  
7. Start the washing programme.  
2. Fill the salt container with dishwasher salt.  
3. Fill the rinse aid dispenser with rinse aid.  
4. Load cutlery and dishes into the dishwasher.  
If you use detergent tablets, refer to the chapter 'Use  
of detergent'.  
Setting the water softener  
The water softener removes minerals and salts from the  
water supply. Minerals and salts can have bad effect on  
the operation of the appliance.  
Water hardness is measured in equivalent scales:  
• German degrees (dH°).  
• French degrees (°TH).  
• mmol/l (millimol per litre - international unit for the  
hardness of water).  
• Clarke.  
Adjust the water softener to the water hardness in your  
area. If necessary, contact your local water authority.  
5
 
Water hardness  
Water hardness setting  
manually electronically  
°dH  
°TH  
mmol/l  
9,1 - 12,5  
7,6 - 9,0  
6,5 - 7,5  
5,1 - 6,4  
4,0 - 5,0  
3,3 - 3,9  
2,6 - 3,2  
1,9 - 2,5  
0,7 - 1,8  
< 0,7  
Clarke  
64 - 88  
53 - 63  
46 - 52  
36 - 45  
28 - 35  
23 - 27  
18 - 22  
13 - 17  
5 - 12  
51 - 70  
43 - 50  
37 - 42  
29 - 36  
23 - 28  
19 - 22  
15 - 18  
11 - 14  
4 - 10  
91 - 125  
76 - 90  
65 - 75  
51 - 64  
40 - 50  
33 - 39  
26 - 32  
19 - 25  
7 - 18  
2
2
2
2
2
2
1
1
1
10  
9
8
7
6
5
4
3
2
1)  
1)  
< 4  
< 7  
< 5  
1
1
1) No use of salt required.  
1. Press and hold the start/cancel button. Turn the pro-  
gramme knob clockwise until the programme marker  
agrees with the first washing programme on the con-  
trol panel.  
2. Release the start/cancel button when the on/off indi-  
cator light and the start/cancel indicator light start to  
flash.  
You must set the water softener manually and elec-  
tronically.  
Manual adjustment  
The appliance is set at the factory at position 2.  
– At the same time, the end-of-programme indicator  
light flashes to show the level of the water softener.  
Example:  
5 flashes, pause, 5 flashes, pause, etc. = level 5  
3. Press the start/cancel button one time to increase the  
water softener level by one step.  
The end-of-programmeindicator light shows the new  
level.  
4. Turn the programme knob to the off position to save  
the operation.  
1
2
Set switch to position 1 or  
2.  
Electronic adjustment  
The water softener is set at the factory at level 5.  
Use of dishwasher salt  
Caution! Only use dishwashers salt. Types of salt  
that are not applicable for dishwashers cause  
damage to the water softener.  
6
 
1
3
2
4
6
5
It is normal that water overflows from the salt con-  
tainer when you fill it with salt.  
Make sure that there is no grain of salt outer of the  
salt compartment. Salt which stays on the tank for  
a while drills the tank. It is recommended to start a wash-  
ing programme immediately after you fill the salt con-  
tainer. This prevents of corrosion because of spilled salt.  
When you set electronically the water softener to level 1,  
the salt indicator light does not stay on.  
Fill the salt container with  
1 litre of water (only the  
first operation).  
Use of rinse aid  
Caution! Only use branded rinse aid for  
dishwashers.  
Do these steps to fill the rinse aid dispenser:  
1
3
2
4
7
 
Adjusting the dosage of rinse aid  
Caution! Do not fill the rinse aid dispenser with  
other products (e.g. dishwasher cleaning agent,  
liquid detergent). There is a risk of damage to the  
appliance.  
The rinse aid dial is set at  
the factory at position 4.  
To increase or decrease  
the dosage refer to 'What  
to do if...'  
Loading cutlery and dishes  
Helpful hints and tips  
Caution! Only use the appliance for household  
utensils that are applicable for dishwashers.  
Do not use the appliance to clean objects that can absorb  
water (sponges, household cloths, etc.).  
• Before you load cutlery and dishes, do these steps:  
– Remove all food remainings and debris.  
– Make burnt, remaining food in pans soft.  
1
2
Arrange service dishes  
and large lids around the  
edge of the lower basket.  
• While you load cutlery and dishes, do these steps:  
– Load hollow items (e.g. cups, glasses and pans)  
with the opening down.  
– Make sure that water does not collect in the con-  
tainer or in a deep base.  
– Make sure that cutlery and dishes do not lie inside  
one another.  
– Make sure that cutlery and dishes do not cover other  
cutlery and dishes.  
– Make sure that glasses do not touch other glasses.  
– Put small objects in the cutlery basket.  
• Plastic items and pans with non-stick coatings can  
keep water droplets. Plastic items do not dry as well  
as porcelain and steel items.  
1
2
Use the cutlery grid. If the dimensions of the cutlery  
prevent use of the grid, remove it.  
• Put light items in the upper basket. Make sure that the  
items do not move.  
Caution! Make sure that the spray arms can move  
freely before you start a washing programme.  
Warning! Always close the door after you load or  
unload the appliance. An open door can be  
dangerous.  
8
 
1
2
1
2
Arrange the items to let  
For longer items, fold the  
Do these steps to move the upper basket to the upper or  
lower position:  
water touch all surfaces. cup racks up.  
Adjustment of the height of the upper basket  
If you put large plates in the lower basket, first move the  
upper basket to a upper position.  
1. Move the front runner stops (A) out.  
2. Pull the basket out.  
3. Put the basket in the upper or lower position.  
4. Replace the front runner stops (A) in their initial po-  
sition.  
Warning! Adjust the height before you load the  
upper basket.  
Caution! If the basket is in the upper position, do  
not put cups on the cup racks.  
Maximum height of the dishes in :  
upper basket  
20 cm  
lower basket  
31 cm  
Upper position  
Lower position  
24 cm  
27 cm  
Use of detergent  
Only use detergents (powder, liquid or tablet) that  
are applicable for dishwashers.  
Follow the data on the packaging:  
• Dosage recommended by the manufacturer.  
• Storage recommendations.  
Do not use more than the correct quantity of deter-  
gent to save an environment.  
3
4
If you use a washing pro-  
gramme with prewash  
phase, put more detergent  
in the prewash detergent  
compartment (B).  
Fill the detergent dispens-  
er (A) with detergent.  
1
2
9
 
tainers. In this condition the rinse aid indicator light stays  
on when the appliance is switched on.  
1. Do a check if these tablets are applicable for the local  
water hardness. Refer to the instructions from the  
manufacturer.  
2. Select the lowest setting for the water hardness and  
rinse aid dosage.  
Do these steps if the drying results are not satisfactory  
1. Fill the rinse aid dispenser with rinse aid.  
2. Set the rinse aid dosage to position 2.  
5
6
Different brands of detergent dissolve in different  
times. Some detergent tablets do not have the best  
To use normal detergent again  
1. Fill the salt container and rinse aid dispenser.  
2. Adjust the water hardness setting to the highest level.  
3. Do a washing programme without dishes.  
cleaning results during short washing programmes. Use  
long washing programmes when you use detergent tab-  
lets to fully remove the detergent.  
4. Adjustthewatersoftenertothewaterhardnessinyour  
area.  
5. Adjust the rinse aid dosage.  
Use of combi detergent tablets  
These tablets contain agents such as detergent, rinse aid  
and dishwasher salt. Some types of tablets can contain  
other agents  
When you use tablets, that contain special salt and rinse  
aid, it is not necessary to fill the salt and rinse aid con-  
Setting and starting a washing programme  
Do these steps to set and start a washing programme:  
1. Close the door.  
• The programme continues from the point of interrup-  
tion.  
2. Turn the programme knob to set the washing pro-  
gramme. Refer to the chapter 'Washingprogrammes'.  
– The on/off indicator light comes on.  
3. Press the start/cancel button.  
Cancelling a washing programme  
• Press and hold the start/cancel button until the start/  
cancel indicator light goes off.  
The washing programme is cancelled.  
At this time you can do these steps:  
1. Switch off the appliance.  
2. Set a new washing programme.  
Fill the detergent dispenser with detergent before you  
set a new washing programme.  
– The washing programme starts automatically.  
– The start/cancel indicator light comes on.  
Whenthewashingprogrammeoperates, youcannot  
change the programme. Cancel the washing pro-  
gramme.  
Setting and starting a washing programme with  
delay start  
1. Set a washing programme.  
2. Press the delay start button.  
– The delay start indicator light comes on.  
3. Press the start/cancel button.  
– The countdown of the delay start starts.  
When the countdown is completed, the washing pro-  
gramme automatically starts.  
Warning! Only interrupt or cancel a washing  
programme if necessary.  
Caution! Open the door carefully. Hot steam can  
come free.  
Interrupting a washing programme  
Open the door.  
• The programme stops.  
Close the door.  
• The delay start indicator light goes off.  
10  
 
• The appliance stops automatically.  
• The end indicator light comes on.  
For better drying results, keep the door ajar for some mi-  
nutes before you remove the dishes.  
Do not open the door during the countdown to pre-  
vent interruption of the countdown. When you close  
the door again, the countdown continues from the point  
of interruption.  
Let the dishes cool down before you remove them from  
the appliance. Hot dishes are easily damaged.  
Cancelling a delay start:  
1. Press and hold the start/cancel button until, the start/  
cancel indicator light and delay start indicator light  
go off.  
2. Press the start/cancel button to start the washing  
programme.  
Removing the load  
• First remove items from the lower basket, then from  
the upper basket.  
• There can be water on the sides and door of the appli-  
ance. Stainless steel becomes cool more quickly than  
the dishes.  
End of the washing programme  
Switch off the appliance in these conditions:  
Care and cleaning  
Warning! Switch the appliance off before you clean  
the filters.  
Cleaning the filters  
Important! Do not use the appliance without the filters.  
Make sure that the installation of the filters is correct.  
Incorrect installation will cause unsatisfactory washing  
results and damage to the appliance.  
3
4
To remove filters B and C, Remove the flat filter A  
turn the handle approxi- from the bottom of the ap-  
mately 1/4 anticlockwise. pliance.  
1
2
Fully clean the filters A, B  
and C below running wa-  
ter.  
5
Put the filter system in po-  
sition. To lock the filter  
system, turn the handle  
clockwise until it locks in  
position.  
Important! Do not remove the spray arms.  
If the holes in the spray arms become clogged, remove  
remaining parts of soil with a cocktail stick.  
11  
 
External cleaning  
If not possible, empty the appliance and close the door.  
Disconnect the water inlet hose and remove water from  
the water inlet hose.  
Clean the external surfaces of the appliance and control  
panel with a damp soft cloth. Only use neutral detergents.  
Do not use abrasive products, scouring pads or solvents  
(acetone, trichloroethylene etc...).  
Frost precautions  
Caution! Do not install the appliance where the  
temperature is below 0 °C. The manufacturer is not  
responsible for damage because of frost.  
What to do if…  
The appliance does not start or stops during operation.  
If there is a fault, first try to find a solution to the problem  
yourself. If you cannot find a solution to the problem  
yourself, contact the Service Force Centre.  
Caution! Switch off the appliance before you do the  
below suggested corrective actions.  
Fault code and malfunction  
Possible cause and solution  
• continuous flash of the start/cancel in- • The water tap is blocked or furred with limescale.  
dicator light Clean the water tap.  
• 1 flash of the end-of-programme indi- • The water tap is closed.  
cator light  
Open the water tap.  
The dishwasher does not fill with water  
• The filter in the water inlet hose is blocked.  
Clean the filter.  
• The connection of the water inlet hose is not correct. The hose can  
be kinked or squashed.  
Make sure that the connection is correct.  
• continuous flash of the start/cancel in- • There is a blockage in the sink spigot.  
dicator light Clean the sink spigot.  
• 2 flashes of the end-of-programme in- • The connection of the water drain hose is not correct. The hose can  
dicator light  
The dishwasher does not drain  
be kinked or squashed.  
Make sure that the connection is correct.  
• continuous flash of the start/cancel in- • Close the water tap and contact your local Service Force Centre.  
dicator light  
• 3 flashes of the end-of-programme in-  
dicator light  
The anti-flood device operates  
12  
 
Fault code and malfunction  
Possible cause and solution  
• The appliance door is not closed.  
The programme does not start  
Close the door.  
• Mains plug is not connected in.  
Put in the mains.  
• The fuse has blown out in the household fuse box.  
Replace the fuse.  
• Delay start is set.  
Cancel the delay start to start the programme immediately.  
After the check, switch on the appliance. The programme • Product number (PNC)  
continues from the point of interruption. If the malfunction  
shows again, contact your Service Force Centre.  
For other fault codes, not described in the chart, contact  
your Service Force Centre.  
These data are necessary to help you quickly and cor-  
rectly:  
• Serial number (S.N.)  
For these data, refer to the rating plate.  
Write the necessary data here:  
Model description : ..........  
Product number : ..........  
Serial number : ..........  
• Model (Mod.)  
The cleaning results are not satisfactory  
The dishes are not clean  
• The selected washing programme is not applicable for the type of load and  
soil.  
• The baskets are loaded incorrectly so that water cannot reach all surfaces.  
• Spray arms do not turn freely because of incorrect arrangement of the load.  
• The filters are dirty or not correctly installed.  
• The quantity of detergent is too little or missing.  
Limescalesparticlesonthedishes • The salt container is empty.  
• The water softener is adjusted on a wrong level.  
• The salt container cap is not closed correctly.  
The dishes are wet and dull  
• No rinse aid has been used.  
• The rinse aid dispenser is empty.  
There are streaks, milky spots or • Decrease the rinse aid dosage.  
a bluish coating on glasses and  
dishes  
Dry water drop signs on glasses • Increase rinse aid dosage.  
and dishes  
• The detergent can be the cause.  
Technical data  
Dimensions  
Width cm  
Height cm  
44,6  
85  
13  
 
Depth cm  
60,5  
Electrical connection - Voltage -  
Overall power - Fuse  
Information on the electrical connection is given on the rating plate on the  
inner edge of the dishwasher door.  
Water supply pressure  
Minimum  
0,5 bar (0,05 MPa)  
8 bar (0,8 MPa)  
9
Maximum  
Capacity  
Place settings  
Environment concerns  
markings, e.g. >PE<, >PS<, etc. Discard the packaging  
materials in the applicable container at the community  
waste disposal facilities.  
The symbol  
on the product or on its packaging  
indicates that this product may not be treated as  
household waste. Instead it should be taken to the  
appropriate collection point for the recycling of electrical  
and electronic equipment. By ensuring this product is  
disposed of correctly, you will help prevent potential  
negative consequences for the environment and human  
health, which could otherwise be caused by inappropriate  
waste handling of this product. For more detailed  
information about recycling of this product, please  
contactyourlocalcouncil, yourhouseholdwastedisposal  
service or the shop where you purchased the product.  
Warning! To discard the appliance, follow the  
procedure:  
• Pull the mains plug out of the socket.  
• Cut off the mains cable and mains plug and discard  
them.  
• Discard the door catch. This prevents the children to  
close themselves inside the appliance and endanger  
their lives.  
The packaging materials are environmentally friendly and  
can be recycled. The plastic components are identified by  
Installation  
Warning! Make sure that mains plug is  
disconnected from the mains socket during  
installation.  
Fitting under a counter  
Put the appliance adjacent to a water tap and a water drain.  
Remove the appliance worktop to install it under a sink  
unit or a kitchen worktop. Make sure that the dimensions  
of the recess agree with the given dimensions.  
1
2
14  
 
Install the appliance worktop to the appliance if you want  
to use the dishwasher as a freestanding appliance.  
The plinth on freestanding appliance is not adjustable.  
Adjusting the level of the appliance  
Make sure that the appliance is level to close and seal the  
door correctly. If the level of the appliance is correct, the  
door does not catch on the sides of the cabinet. If the door  
does not close correctly, loosen or tighten the adjustable  
feet until the appliance is level.  
3
4
Water connection  
Water inlet hose  
Connected the appliance to a hot (max. 60°) or cold water  
supply.  
If the hot water comes from alternative sources of energy  
that are more environmentally friendly (e.g. solar or pho-  
tovoltaic panels and aeolian), use a hot water supply to  
decrease energy consumption.  
Drain hose  
max 85 cm  
min 40 cm  
Connect the inlet hose to a water tap with an external  
thread of 3/4”.  
Caution! Do not use connection hoses from an old  
appliance.  
1
2
Connect the water drain  
hose to the sink spigot.  
The water pressure must be in the limits (refer to the  
chapter 'Technical data'). Make sure that the local water  
authority gives you the average mains pressure in your  
area.  
Make sure that there are no kinks in the water inlet hose  
and that the water inlet hose is not squashed or entangled.  
Turn the inlet hose to the left or the right to suit the in-  
stallation. Fit the locknut correctly to prevent water leaks.  
Caution! Do not connect the appliance to new pipes  
or pipes that are not used for a long time. Let the  
3
4
water run for some minutes, then connect the inlet hose.  
The internal diameter must not be smaller than the diam-  
eter of the hose.  
If you connect the water drain hose to a trap spigot under  
the sink, remove the plastic membrane (A). If you do not  
removethe membrane, remainingfoodcan cause ablock-  
age in the drain hose spigot.  
Caution! Make sure that the water couplings are  
tight to prevent water leakage.  
15  
 
Electrical connection  
Warning! The manufacturer is not responsible if  
you do not follow these safety precautions.  
Ground the appliance according to safety precautions.  
Make sure that the mains plug is accessible after  
installation.  
Do not pull the mains cable to disconnect the appliance.  
Make sure that the rated voltage and type of power on the Always pull the mains plug.  
rating plate agree with the voltage and the power of the  
Warning! The appliance is supplied with a 13 amp  
local power supply.  
plug attached. Use a 13 amp ASTA approved (BS  
1362) fuse if it is necessary to change the fuse in the plug  
supplied.  
Always use a correctly installed shockproof socket.  
Do not use multi-way plugs, connectors and extension  
cables. There is a risk of fire.  
Do not replace the mains cable yourself. Contact the  
Service Force Centre.  
16  
 
17  
 
18  
 
19  
 
To buy accessories, consumables and spare parts at our online shop please visit:  
 

Weil McLain Boiler CGt SERIES User Manual
West Bend Back to Basics Blender SUP400BINST User Manual
Whirlpool Computer Monitor WGD6200S User Manual
Woodstock Saw W1824 User Manual
Xerox Printer M20 User Manual
Yamaha Music Mixer MB02R96 User Manual
Zanussi Freezer 110026 User Manual
Zanussi Plumbing Product 132332 User Manual
Zanussi Refrigerator Z 56 3 SA User Manual
Zanussi Ventilation Hood 642000 User Manual